Wheel Speed Sensor Replacement - it's easier than you think
2011年7月30日 · Crawl up under the Jeep and you'll see the sensor. Unplug the sensor then take an 8mm or 9mm (I don't remember which) wrench and unbolt it. The sensor pulls straight out. Put some DE on the new one and slide it back in. Make sure the bolt hole lines up and replace the bolt and plug it back in.
Wheel Speed Sensor Replacement - it's easier than you think
2010年4月6日 · A lot of other forums listing a lot of random stuff. Yours described my problem exactly. I crawled under my jeep and sure enough the wheel speed sensor wire for my drivers front wheel is nearly cut in two. Just ordered my new wire for $16 on ebay using the part number you provided. Had to sign up for this forum just to express my gratitude.
Wheel Speed Sensor Replacement - it's easier than you think
2009年12月11日 · The front speed sensor comes with a section of wiring that is about 14 or 16" long (guesstimate) that you plug into your Jeep's wiring harness. The rear speed sensor comes with no wiring since your Jeep's wiring harness plugs right into the sensor at the wheel. Ron, hopefully I'm muddying up your write-up.
Wheel Speed Sensor Replacement - it's easier than you think
2018年1月27日 · Write Up Dept. (The Library) Wheel Speed Sensor Replacement - it's easier than you think. Jump to Latest
ABS Sensor/wheel speed sensor | JKOwners Forum
483 posts · Joined 2009. #13 · Sep 12, 2009. mtnmedic, your trouble codes refer to communications over CAN bus C, not the wheel sensors. Wheel sensor problem codes are preceded by the letter C, not U. The FSM says your codes are a problem with the Powertrain control module, the antilock brake module, or the wiring in between.
ABS light on, no error codes, replaced wheel speed...
2015年3月31日 · Back in March, I replaced the rear axle shafts with Ten Factory Chromoly shafts after twisting the splines and bending the flange on the stock shafts. However, as soon as I swapped them out, the ABS and ESC lights came on. Puzzled, I picked up a new set of speed sensors from Mopar. No change, ABS and ESC lights still on.
Grease on ABS sensor normal? - JKOwners Forum
2012年7月5日 · S. ShafferNY Discussion starter. 348 posts · Joined 2011. #1 · Jul 5, 2012. Recently my Jeep threw the ABS/ESP/traction control lights. I pulled the wheel speed sensor on the front driver's side and I noticed it was covered in white grease. I'm assuming this is the first indication of a wheel bearing failure, so I ordered two new unit bearings.
Wire harness for rear wheel speed sensor - JKOwners Forum
2013年3月1日 · To acquire that harness you may need to purchase the ENTIRE harness including the all the other sensor connectors connected to it. Which would be pricy and labor intensive. Again I could be wrong. Just what I've experienced being a dealership tech at Ford. Don't know much about Jeep dealer parts departments. Hope this helps.
Wheel Speed Sensor Wire Extensions? - JKOwners Forum
2011年1月23日 · 1519 posts · Joined 2010. #3 · Jan 23, 2011. I hear ya there. If I had found the electric locker connectors I wouldn't have 90% of a $70 wiring harness laying in a pile next to the jeep. 2007 Sahara Unlimited - Dana 60/14 Bolt - 5.38's with ARBs - 40x13.50x17 Goodyear MTRs - 3.5" Rock Krawler X Factor Plus - Rubi Rock Rails - XRC 10,000lb Winch.
can i splice Abs wires - JKOwners Forum
2011年3月4日 · Pull out as much slack as you can, then strap them down with zip ties at the brake line unions. The rears are a snap, just unlatch the connectors at the wheel speed sensors, push out the zip tie at the control arm bracket on the axle, run the wires over the top of the axle tube (instead of underneath) and reconnect at the sensor.